2015 XT1000 Commander - secondary Clutch Bolt - Can-Am Commander Forum
 
LinkBack Thread Tools Display Modes
post #1 of 4 Old 08-12-2019, 05:14 PM Thread Starter
Junior Member
 
Join Date: Aug 2019
Posts: 1
Unhappy 2015 XT1000 Commander - secondary Clutch Bolt

Hello, I am a new member. I bought my XT1000 Commander last summer it is a 2015 and had like 5,880 miles on it. I have kept blowing belts and doing research. I now bought a clutch kit (primary & Secondary) from Adam at Airdam. I can't wait to get it in and rolling again. Unfortunately i cannot get the secondary bolt out. It has two nuts on the end of it (17mm) and my clutch came off with some difficulty as the exhaust pipe was in way as the bolt did not come all the way off and is sticking out 4.5 inches....the nuts came off but now how the heck do i get the dang bolt out so i can put new kit in? I put a washer inbetween the two bolts and just turn left on the inside nut and have the XT in reverse gear...but it still moves...not the bolt but it turns everything. I attached a picture of it.

Thank you in advance! I hope i don't have to end up bring it to a mechanic (all my money went to Airdam). I hope someone here has knowledge or experience with this same propblem. Thank you!
Attached Thumbnails
Click image for larger version

Name:	Seconary Bolt - 2015 XT1000 Commander.jpg
Views:	13
Size:	3.32 MB
ID:	60959  
Dale19 is offline  
Sponsored Links
Advertisement
 
post #2 of 4 Old 08-12-2019, 06:14 PM
Super Moderator
 
acefire's Avatar
 
Join Date: Aug 2012
Location: Charleston WV
Posts: 22,525
Use heat on the bolt not the shaft start heating about one inch back from the shaft . They normally have loctite on them the heat will liquefy the loctite.
acefire is offline  
post #3 of 4 Old 08-12-2019, 07:06 PM
Senior Member
 
Boogerhead's Avatar
 
Join Date: Nov 2014
Location: Henderson CO
Posts: 7,276
Welcome. Lots of good folks and advice here. Good luck! Boog.


Sent from my iPhone using Tapatalk

I may have to grow old, but you can't make me grow up!
Boogerhead is offline  
Sponsored Links
Advertisement
 
post #4 of 4 Old 08-13-2019, 10:06 AM
Senior Member
 
Troy's Avatar
 
Join Date: Feb 2012
Location: Grimshaw
Posts: 12,492
I would wrap sand paper on the shaft and then put a visegrip over the sand paper to help hold the input shaft once your ready to try to remove the stud


Sent from my iPhone using Tapatalk

A list of mods extreme bumper,hid lights,led light bar,powersteering,rackzilla,customlift;outlaw tires,beadlocks,dual batterys dual exhaust,dualwinchs,full warn skids custom cab,heater ,black box,clutchkit,roof,tunes,gorilla frontaxles,2013QE diff,custom built front driveshaft,pipewrap,low sport ,blower, fan over ride, BEST MOD maverick rear diff,quiet and tuff , turner rear axles, custom center console cover that controls all heat and noise IM DONE.............
Troy is offline  
Reply

  Lower Navigation
Go Back   Can-Am Commander Forum > New Member Area > New Member Introductions & Site Assistance

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
2011 Commander 1000 secondary clutch 1000Rider New Member Introductions & Site Assistance 3 11-17-2018 04:05 PM
2015 Can Am Maverick 1000 XT Primary Clutch and gold secondary spring Cainer51 Commander Parts and Products For Sale 0 01-18-2018 06:50 PM
2015 Commander XT1000 robdog Commanders For Sale 3 01-14-2018 06:31 AM
QRS secondary on Commander BluMtn Commander Performance Modifications 5 01-15-2017 12:57 PM
2015 Secondary bolt??? nsudemon46 Commander General Discussion 9 01-03-2016 12:13 AM

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome